Powered Electric Fin – For Paddle Boards

Includes:
 Brushless Motorized fin
 Wireless Remote control
 High Efficient lithium Battery

 Charger

​

 Power or boost the speed of your SUP.

Use the Power fin for touring, fishing, recreation, lessons or as a board speed booster.

The PowerFin fits in a standard SUP or surfboard centre fin box.

A multi-speed remote control, the fin with motor,

battery in water resistant case and a battery charger are included.

​

BATTERY CASE

Battery case is water resistant ( IP67). Features an on -off switch, 1 charge port, and 1 power cable port.

The battery should be lashed securely to the board deck via, bungee cords on 2 to 4 tie down plugs ,

or with a 1” tie down strap, around the entire board if your board does not have rear tie down plugs.

The Electric Fin battery should be charged for 6hours before use.

​

BATTERY CHARGE LIFE:
 1 gear 2mph - ( Battery can work 10 hours )

 2 gear 3mph –(Battery can work 5 hours)

 3 gear 5mph – ( Battery can work 2.5hours )

 

BATTERY SPECIFICATION:
 Rated voltage : 36VOLT
 The battery capacity: 12AH

​

CHARGER:
 Rated current: 2A

 Rated voltage: 36V

​

Strap or bungee the battery to board.

PLACE STRAPS UNDER CARRY HANDLE.
Rinse off fin and battery after each use.

Always check to make sure all connections are tight.

​

 DC Charging Plug
 Drive motor cable Plug  Power Switch ( on/off )

 Never open battery case around water.
 Keep fingers and toes away from propeller.
 Warranty 1 year on motor and battery under normal, non commercial, use.

 

REMOTE CONTROL

Remote control is water resistant to 3 meters.

Remote control has 3 mode buttons .
-- Power / speed increase to propeller -- Propeller power off
-- Decrease speed of propeller

​

ASSEMBLY

Make sure to setup board on a dry or grassy area to protect your equipment.
Fin install. Place E‐fin base in board box such that the end with the pin slides into the box slot.

Make sure the screw plate is in box, and screw removed.

Slide fin back then press the forward part of the fin base into the box.

Align metal screw plate hole with fin base hole, pass screw through to plate and secure.
ALWAYS, wear a leash secured to SUP when using the Power Fin.

 The leash will keep you attached to board, so it cannot get away when powered.

Remote control may not be in range of battery internal controller to allow cut off of motor if a leash is not worn.

Damage to fin due to impact or abuse is not covered.
If water gets into battery box warranty is void
Make sure all ports have water tight plugs in before operating.

​

SAFETY
THERE IS A RISK OF SERIOUS INJURY,OR DEATH FROM DROWNING.

​

Power fin is for paddle boards, and electric paddle sports can be dangerous and physically demanding, more so with higher speed with fin. The user of this product acknowledges, understands, and assumes the risks involved in paddle sports. It is the responsibility of the user to familiarize themselves with all operating

procedures, and to know local laws. Always wear a coast guard approved PFD (Personal Flotation Device)

As well as a leg leash. This fin is used on paddle board, so just do what you do on a SUP board.

Not to jump or perform acrobatics on. Only stand or sit on this board. When in the water and not on dry land.

•   Always wear an approved PFD and leg leash.

•   Check all the equipment prior to usage, especially the fin connections to battery.

•   Do not operate under the influence of drugsor alcohol.

•   Children must be supervised by a responsible adult at all times.

•   Do not exceed your padding ability; and know your limitations.

•   Check weather forecasts and conditions.

•   Be aware of tide, currents, depth conditions, and your marine environment.

•   Avoid sharp objects.

•   Discard packing materials, they can cause suffocation.

•   Never underestimate Mother Nature.

​

• MAINTENANCE

•   Periodically check and observe condition of the fin, battery and all accessories.

•   Be sure to clean with fresh water and even a mild soap solution if there is any lingering residue from 

  the elements. ( Do not use detergents, abrasive cleaners, or silicon based products. )

•   Remove battery and fin from board and clean them separately.

•   Store everything dry and in a dry area.